Fits the following models: vehicle list

The 1,2,3-ignition is fully electronic and is simply used instead of the original ignition distributor.
Advantages: You can return the original part and upgrade at any time. Other solutions are placed on the old unit and take over its accuracy, eg Shock wave side by leaking storage etc.

Freely programmable, two ignition curves can alternately be accessed during operation. Allows best fit the ignition curve to the engine by comparison.

The top model with app interface for monitoring via mobile phone. Your mobile is the engine test bench!

Chrome trim kit for Mercedes-Benz Ponton Cabrio + Coupé in raw brass with good quality, 10 pieces (complete set only).

MB-reference number: 120 781 0321 and 120 781 0421

2nd Type "long", show not for the folding roofs in the open state, the folding back of the sky. He disappears into a kind of tape. Approximately up to yoc 56 these parts were built for rooftops.

MB reference anchor plate: 120 781 0020, threaded plate: 120 657 0011

The wind deflector ensures that any turbulence created in the interior. This can be especially troublesome in the back seat. We can supply the acrylic glass to replace an already built-in Webasto wind deflector, which was damaged. Brown tint, stable design with holes for the original Webasto hinge.

Referenz-Bestellnummer bei Mercedes: 120 671 0020

MB-ET Reference Number: 30 136 779 0036

We only sell in pairs.

MB-ET-Reference: replaces 120 758 0127 (if the lid does not hold in "open position" on its own)

We only sell in pairs.

Spare plan number: 74 - no: 180 616 0171

This metal sheet is welded firmly in a convertible for reinforcement of the soil. We have made it in the sheet thickness of 2mm.

Spare plan number: 59a - no: 30 180 616 0167

On the drawing part 59 and 60. We have manufactured this sheet in two parts, 59a and 59b now = driver's side, as well as 60a and 60b = passenger side. Usually a part sheet is sufficient to repair, and one wants to save as much as possible from the original sheet substance.
The original, evaginated water processes are executed as in the original, see spare plan.

Spare plan number: 60a - no: 30 180 616 0267

On the drawing part 59 and 60. We have manufactured this sheet in two parts, 59a and 59b now = driver's side, as well as 60a and 60b = passenger side. Usually a part sheet is sufficient to repair, and one wants to save as much as possible from the original sheet substance.
The original, evaginated water processes are executed as in the original, see spare plan.

Spare Parts diagram No. 74

Meanwhile Ponton C / C have matured to high-quality vintage cars. So you should work here with a corresponding to the original repair panel including beading. The Repair Panel manufactured by us is made to the experience gained in numerous Ponton C / C Restorations and fits good.

Spare Parts diagram No. 71 - 180 640 0172

The rear fender was only available as a complete rear wing for welding at Mercedes. However, as often only the fender edge is rusted and you now this is important to save as much original substance as possible, we have developed here section Repair sheets. The marker shows which area occupies the repair sheets on the fender.
This sheets can be found around the wheel arch (where also the wheel arch chrome takes place) and above. Here the condensate collects and creeps into the seam between outer and inner fenders. Seal after repairs. Frequent drivers see Edge rust protection Karos (www.lokari.eu). The plate is made in two parts, as the vehicle lengths at Ponton coupe and convertible due to the manual production up to 2cm may be different lengths. Through the division, you can compensate for these variations in length better. Best directed you look after hopefully still present Radlaufchrom to restore the original as possible. Should the wheel arch chrome be missing, even those we perform as a complete set in our range.

Should be ailing under the taillight of your rear fender, also here we offer single repair section sheets, as for the inner wheel arch.

Also for the wheel arch itself, Mercedes-reference "wheel arch outside left" Plan no. 20 (ETNr: 180 647 0375 Cabrio / ETNr: 180 647 0775 Coupé) and "wheel arch outside right" Plan no. (ETNr: 180 647 0475 Cabrio / ETNr: 180 647 0875 coupe) are metal sheets available.

ter processes are executed as in the original, see spare plan.

Spare Parts diagram

Spare plan number: 2 - no: 180 880 0718